Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Fence Installation: The Thousand Oaks Owner’s Guide
Unilock fence installation in Thousand Oaks typically runs $3,500 to $9,000 complete, depending on linear footage, post depth, and whether we’re building fresh or replacing failed sections. We stock Unilock-compatible fence components and can usually start within a week of your written estimate. Most homeowners call us after a fence post shifts out of plumb or a panel cracks at the base, and they want to know if the whole run needs to come out or just the damaged section.
Here’s what we see most often: the fence looked fine for years, then one wet winter or a hard Santa Ana wind exposed a weak point. Maybe a post settled because the original installer cut corners on the footing. Maybe the panel joint separated at the corner where two grades meet. The good news is Unilock fence systems are modular, which means we can usually replace sections without tearing out the entire run. Isaac Pruett has walked enough Thousand Oaks properties, from Lang Ranch to Newbury Park, to know which failures are repairable and which ones mean a full re-set.
Key Takeaways:
- Unilock fence installation in Thousand Oaks averages $3,500 to $9,000 installed
- Modular design means partial replacement is often possible
- We deliver a written price before any work begins, every time
- Every crew member arrives with a photo ID badge and is introduced by name before the visit
- 365-Day Done Right Promise covers the installation for a full year
Which Unilock Models This Applies To
Unilock fence systems fall into two broad categories: precast concrete panel fences and segmental retaining-wall-style fences built from Unilock block. The precast panel systems, including the Estate Wall and Bella Vista lines, use interlocking concrete panels that slide into grooved posts. The block-style fences use Unilock’s standard wall units, typically from the Brussels Dimensional or Rivercrest Wall lines, stacked and capped with a matching coping unit. Each system takes different post spacing, different footing depths, and different joint treatments, so matching the right part starts with identifying the system you already have.
Here’s the compatibility gotcha we see in Thousand Oaks: precast Unilock panels are not universally interchangeable across product generations. A panel from the current Estate Wall line will not always seat correctly in posts from the discontinued Country Manor fence series, even if the dimensions look close on a tape measure. The post channel width differs by as little as 1/8 inch, and that’s enough to cause a wobble that gets worse every season. Before ordering parts, we measure the existing post channel and the panel tongue thickness, then match against Unilock’s current spec sheets. We also check for the molded product code on the back face of the panel, which older panels sometimes still show.
One more thing worth knowing: Unilock’s wall block lines get revised periodically, and a block made in 2019 may have a slightly different face texture or height tolerance than one cast in 2024. If we’re adding to an existing fence run, we order from a production batch that matches your existing units as closely as possible. For that reason, we often recommend budgeting for a few extra matching blocks when we do the original install, so future repairs don’t create a visible patch. Mismatched block faces are the kind of detail that shows up in afternoon light, and you’ll notice it every time you pull into the driveway.
Mason Remodeling Co Thousand Oaks is an independent service provider, not affiliated with Unilock. We install and service Unilock fence systems because we know the product line well and can source genuine components through our supplier relationships. We also stock parts for KraftMaid, Cambria, and Silestone, so fence work is one part of what our crews handle across Thousand Oaks.
Styles & brands we work with
Signs Your Unilock Fence Installation Is Failing
- Post lean or tilt. A post that’s moved more than a few degrees off vertical almost always means the footing was undersized for the soil it’s sitting in. Thousand Oaks clay expands and contracts with seasonal moisture, and a post set in a shallow or narrow footing will slowly work its way out of plumb.
- Panel separation at the joints. When panels pull apart at the seams, you’re usually looking at post movement or a failed adhesive joint. Small gaps let water in behind the panel, which accelerates freeze-thaw cracking in Ventura County’s occasional cold snaps.
- Cracked or spalled panel faces. Hairline cracks at the bottom third of a panel point to settlement or frost pressure. Spalling, where the concrete face flakes away, often traces back to trapped moisture and poor drainage behind the fence line.
- Loose or wobbling panels. If a panel rattles when you push on it, the tongue-and-groove connection has likely worn or the post channel has widened. This is a warning sign that high winds could pull the panel out entirely.
- Visible rust stains around post bases. Rust-colored streaks usually mean the post’s internal reinforcement is corroding, often because the post wasn’t sealed at the base or the footing traps water against the steel. This is structural, not cosmetic.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Thousand Oaks, Unilock fence installation and replacement runs $3,500 to $9,000 on average. A short run of 30 to 40 linear feet with standard precast panels and simple soil conditions lands near the bottom of that range. A longer run, a block-system rebuild, or a job that requires removing an existing fence and hauling debris will push closer to $9,000. The biggest cost drivers are linear footage, whether we’re removing old materials, post depth and footing requirements, and access to the site, since Thousand Oaks hillside lots sometimes require hand-carrying materials when a truck can’t get close.
What we include in every quote: all Unilock-compatible panels or block, posts, concrete for footings, joint treatment, cleanup, and haul-away of old materials. Nothing is left out and then added back as a change order. We put the price in writing before any work starts, and the number on that sheet is the number you pay. If the work fails within 365 days from the completion date, we come back and make it right at no cost to you. That’s the Done Right Promise, and it applies to every Unilock fence installation we do in Thousand Oaks.
DIY or Call Us?
You can safely check a few things on your own: walk the fence line and note which posts are out of plumb, whether panels are separating, and whether any cracks are growing. Take photos and measure the affected sections. That information helps us give you a faster, more accurate estimate.
Where DIY goes wrong is in the actual repair. Unilock precast panels are heavy, and removing one without the right lifting technique can crack the panel you’re trying to save or injure the person doing the lifting. Setting posts correctly means digging footings to the right depth for Thousand Oaks soil, which varies from rocky hillside substrate to expansive clay, and getting the drainage wrong means the same repair again in three years. This is also not a one-person job. A full panel weighs more than most homeowners expect, and a dropped panel doesn’t just break; it can take a hand or foot with it. We’d rather you call (805) 309-3386 and let our crew handle the heavy work than risk an injury on a Saturday. Estimates are free.
FAQs
A properly installed Unilock precast fence should last 25 to 40 years in Thousand Oaks before the panels or posts show structural fatigue. Block walls from Unilock can exceed 50 years when the footing is right. The weak points are post footings in expansive clay soil and joint seals, which may need attention every 8 to 12 years. Call (805) 309-3386 if you’re seeing early cracking or movement, and we’ll tell you whether it’s a footing issue or a material defect.
Yes, in many cases a failed section can be repaired without replacing the whole fence. If one post has shifted or one panel has cracked, we can often pull the damaged component and reset or replace it. The exception is when the original footings were undersized across the entire run, in which case a full re-set is usually the better investment. We’ll tell you which one you’re looking at, and the estimate is free.
Most Thousand Oaks Unilock fence installations take 2 to 5 working days, depending on the length of the run, the footing conditions, and whether we’re removing an old fence. Smaller repairs often take a single day. We schedule work in writing and we show up when we say we will, because Isaac Pruett believes clear communication is half the job no matter what you’re building.
We keep common Unilock-compatible panels, posts, and caps in our inventory, and we can source specific product lines through our suppliers quickly. If you have a discontinued Unilock series, we’ll verify measurements before ordering so we don’t show up with the wrong part. Tell me what you need done. We’ll tell you what it costs and how long it takes, then we’ll do exactly that.
Ready to get your fence fixed? Call (805) 309-3386 for a free estimate. You’ll get a written price before any work starts, and the crew that shows up will be background-checked, uniformed, and introduced by name and photo before they set foot on your property.
Written by Isaac Pruett, Owner, Mason Remodeling Co – Thousand Oaks, CA at Mason Remodeling Co Thousand Oaks, serving Thousand Oaks and nearby areas.
